Search found 78 matches
- Wed Nov 23, 2016 10:53 am
- Forum: Places to Camp
- Topic: Place to park B around Georgia in March 2017
- Replies: 0
- Views: 5828
Place to park B around Georgia in March 2017
Our first 3 races of 2017 are in the Georgia area. 3/5 Union SC, 3/12 Palatka FL and 3/26 in Sparta GA. Me and my Girl live in NJ and are thinking of keeping the B and my race bike parked in the Georgia area and commuting back and forth by train or bus, picking up the B on the Saturday before the ra...
- Mon Aug 29, 2016 1:57 pm
- Forum: Generators
- Topic: Photos of 1994 generator exhaust?
- Replies: 5
- Views: 8507
Re: Photos of 1994 generator exhaust?
Just a follow up on my gen pipes. I purchased the correct thin wall .052 tube with a OD of 1.250 from a company called Stock Car Steel in North Carolina. Also purchased a Onan resonator 155-2449. Purchased a cheep ($50) used hand pump hydraulic pipe bender sold by Harbor Freight and went to playing....
- Tue Aug 16, 2016 12:29 pm
- Forum: Exterior
- Topic: busted bedroom window?
- Replies: 5
- Views: 6971
Re: busted bedroom window?
Just a little update on my bedroom window. The window is now manufactured by Guardian in the USA and was drop shipped from them. The seal and lock were drop shipped from airstream. The cost of the glass 195329-167 is $534.72. The seal 195329-168 was $2.33 a ft. and the lock 195329-166 was $1.87 a ft...
- Mon Jul 18, 2016 3:07 pm
- Forum: Generators
- Topic: How to remove the generator
- Replies: 4
- Views: 7819
Re: How to remove the generator
When I replaced the fuel line on my generator, (94) I just removed the exhaust and retaining bolts from underneath. Their was plenty of hose and cable to slide the generator out before disconnecting it. I have a hydraulic table (any table approximately the right height would work) and slid it out th...
- Thu Jul 14, 2016 12:39 pm
- Forum: Generators
- Topic: Gen fuel line
- Replies: 2
- Views: 6375
Gen fuel line
I was having problems from time to time with the generator just quitting after it has run for awhile. Replaced the fuel filter with a new 1/4 inch one but used a clear one. Seemed to fix it but notice the filter was full of air and only had fuel in the very bottom. When the generator would quit I no...
- Wed Jun 29, 2016 8:59 am
- Forum: Electrical
- Topic: Ignition feed to fridge relay?
- Replies: 2
- Views: 4886
Ignition feed to fridge relay?
I ran across a few problems with the fridge on our 94. My girl left the fridge on 12V when we got home (I forgot too!) and the house battery was dead. Figured someone rewired it so I would make it a point to make sure it was turned off. After the race at Snowshoe WV when we got home the fridge was D...
- Tue Jun 28, 2016 10:23 am
- Forum: Drivetrain
- Topic: Auto fluid
- Replies: 3
- Views: 7004
Re: Auto fluid
Here in the states the bottles say DexronIII/Mercon When I rebuild the transmission in my B I used Valvoline full synthetic DexIII/Merc. I usually just recommend a brand name fluid but I always put the good stuff in my own vehicles. Edit: I was on a UK sight and the listings are way different then h...
- Tue Jun 28, 2016 10:17 am
- Forum: Interior
- Topic: Shower/Tub rehab of Keystone's '94 van
- Replies: 15
- Views: 20404
Re: Shower/Tub rehab of Keystone's '94 van
Me and my girl did exactly the same rehab on our 94 thanks to Keystone's post. We went a couple step further and removed the tub to refinish it so we could reseal the inside edge when it was installed. It also gave me a chance to put a couple of 2X4 support legs under the tub support. And we replace...
- Thu Jun 23, 2016 5:56 pm
- Forum: Drivetrain
- Topic: Auto fluid
- Replies: 3
- Views: 7004
Re: Auto fluid
1996 takes Mercon. Basically the bottle should say Dexron/Mercon. A pan service with filter will take 7-8 quarts You can drain the converter through the rubber plug on the bell housing lining up the 7/16 plug with the hole for another 5-6 quarts. The transmission will hold approximately 16 quarts dr...
- Mon Jun 13, 2016 2:49 pm
- Forum: Exterior
- Topic: busted bedroom window?
- Replies: 5
- Views: 6971
Re: busted bedroom window?
Yes it was the large one up front. I found your thread "save your upper front windshield" after putting the part # in the search box. A picture says a thousand words! Especially the one with the manufacturer and the word "LAMINATED!" I don't know what moron would have replaced th...
- Mon Jun 13, 2016 12:36 pm
- Forum: Exterior
- Topic: busted bedroom window?
- Replies: 5
- Views: 6971
busted bedroom window?
Cruising down the road doing about 65-70 and all of a sudden the bedroom glass shatters blowing safety glass around and nearly giving my girl a hart attack. Looking at the replacement window, it is curved. The glass that was in the B if I can remember might have been flat? And it definitely wasn't l...
- Tue Feb 23, 2016 11:18 am
- Forum: Generators
- Topic: Photos of 1994 generator exhaust?
- Replies: 5
- Views: 8507
Re: Photos of 1994 generator exhaust?
Thanks Keystone. I see now that it is actually one complete piece of pipe, not multiple components.
- Sun Feb 14, 2016 11:51 am
- Forum: Generators
- Topic: Need help with Gen Pipes!
- Replies: 1
- Views: 5701
Need help with Gen Pipes!
I could really use some help on the pipe configuration on the B190's Gen pipes. I believe the 92-96 should be the same. Not a single muffler shop can bend pipe smaller then 1.5"(1.65 in exhaust talk). I was thinking of using 1" conduit and bending and swaging it myself. but if anyone can h...
- Tue Jan 26, 2016 1:50 pm
- Forum: Generators
- Topic: Photos of 1994 generator exhaust?
- Replies: 5
- Views: 8507
Photos of 1994 generator exhaust?
I kinda feel that the exhaust on my generator is going to be more then one kit. I can't find any information or a parts list for the pipes. From where the hanger is near the front of the rear tire and the pipe kits available I would guess I might need at least 3 kits. If anyone has some pics and One...
- Sun Jan 17, 2016 11:33 am
- Forum: Interior
- Topic: Bonding agent
- Replies: 2
- Views: 6929
Re: Bonding agent
Thanks for the info. I have found out what the pale green stuff was. Simply Bondo (or another brand)! It seems that the wood which in this section is the only press board I have found in the B190 so far, wasn't properly prepped. The bondo adhered to the fiberglass very well but not so good to the bl...